# Peripherals > This article describes supported add-on peripherals for RouterBOARD hardware devices. # Peripherals This article describes supported add-on peripherals for RouterBOARD hardware devices. ## Cellular modems RouterOS v7 supports the following cellular modems: - MikroTik modems. - Third-party modems supported by device class/type: - MBIM class USB interface - USB-CDC class USB interface - RNDIS type USB interface - Third-party modems with added support (see the modem table below). ## Please note - Not all modems are listed in the supported modem table. Some modems may work even if not listed because modem manufacturers often re-use the same hardware IDs, and vice versa. - Customized, localized, or locked units may have compatibility issues. - Third-party modems may require configuration adjustments before they can be used with RouterOS. - For mini-PCIe modems with a USB3.0 interface installed in a mini-PCIe slot with PCIe/USB2.0 support, the USB speed must be limited to USB2.0, or the mini-PCIe shared PCIe/USB3.0 pin must be isolated. See the picture below the table. ## Cellular modems | Model | vendor-id | device-id | Tested RouterOS version | Comments | Format | | :-- | :-- | :-- | :-- | :-- | :-- | | Alcatel IK40 | | | v6.41RC11 | LTE interface, Modem can be configured only through modem's configuration WEB page. | USB | | Alcatel IK41 | | | v6.48 | Config-less LTE interface | USB | | Android usb tethering interface | | | v6.7 | Some settings are ignored. | USB | | AnyData ADU-E630WH | | | v6 | ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") | USB | | Anteniti 3372h-153 | | | 7.12 | | USB | | BandRich C501 | | | v5.25 and v6.0 | | USB | | Cinterion LTE Modem | 0x1e2d | 0x0061 | v7.14 and higher | LTE interface, some settings are ignored. Not full SMS functionality. | MiniPCI-e | | D-link DWM-157 | 0x2001 | 0x7d02 | v6.xx | Works! Data Channel: 2, Info Channel: 3, Modem Init: AT+CFUN=1, vendor-id="0x2001" device-id="0x7d02" Some info from modem: > H/W Ver.: B1, F/W Ver.: 2.0.1eu, revision: +CGMR: MOLY.WR8.W1231.DC.WG.MP.V3, 2013/04/09 02:08 Different HW revisions might not work with RouterOS | USB | | D-link DWM-222 | | | See comments | Multiple modem versions with the same marketing name exist: H/W ver: A1 - supported as config-less LTE interface from RoS v6.38Modem firmware version starting from "2.1.4EU".H/W ver: A3 - works as config-less LTE using modem firmware provided RNDIS interface (RouterOS v7 only) | USB | | Dell DW5821e | | | v7.4beta4 and higher | MBIM driver. Revision: T77W968.F1.0.0.5.2.VZ.013 044 | M.2 | | Dell DW5821e-eSIM | 0x413c | 0x81e0 | 7.11 and higher | MBIM driver. FW: T77W968.F1.0.0.5.2.GC.013. "at-chat" support added | M.2 | | DELL T99W175 | 0x05c6 | 0x90d5 | 7.16 and higher | MBIM driver. FW: T99W175.F0.1.0.0.9.GC.004. "at-chat" support added | M.2 | | Dell Wireless 5530 HSPA | | | v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs to manually change profile by command AT\*ENAP=1,1) | MiniPCI-e | | Ericsson F5521gw | | | v6.x and higher | | MiniPCI-e | | Fibocom FM150-AE/FM150-NA | 0x2cb7 | 0x0111 | v7.1beta5 | MBIM driver. Revision: 89603.1000.00.01.01.03 | M.2 | | Fibocom NL-952-EAU | | | v7.1beta5 | MBIM driver. Revision: 19600.7000.00.04.01.05 | M.2 | | Marvell PXA1802 based modems | 0x1286 | 0x4e31 | v7.2.2 | | mini-PCIe | | Huawei E153 | | | v6.31 and higher | | USB | | Huawei E171 | | | v6.xx | Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB | | Huawei e3131 | | | v6.xx and higher | ppp interface | USB | | Huawei E3372h, E5576h, E8372h | 0x12d1 | 0x14db | v6.8 | Config-less LTE interface for modems with vendor-id="0x12d1" device-id="0x14db" Models with suffixes -320 and -608 will not work with RouterOS v6, please use v7 instead Models with suffixes -325 work only with arm cpu | USB | | Huawei E3276-150 | | | v6.xx | ppp interface | USB | | Huawei E3351 | | | v6.24 and higher | | USB | | Huawei E3531 | | | v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim is supported only from RouterOS V7 | USB | | Huawei e398 | | | v6.xx and higher | ppp interface | USB | | Huawei E5377 | | | v6.36.1 | MIFI unit. No serial support, but works with IP on LTE interface | USB | | Huawei E5673s-609 | | | v6.xx | LTE interface | USB | | Huawei K5160 | | | v6.37 v7.0beta6 | v6 and v7 - config-less LTE interface v7 - by default will try to use the modem in MBIM mode | USB | | Huawei K5161 | | | v6.47 | Config-less LTE interface | USB | | Huawei ME909s-120 | | | v6.28 | Recommended modem firmware version 11.617.24.00.00. To reduce LTE interface IP subnet mask to /32 configure modem with at-chat command: `/interface/lte/at-chat [find]` input="AT^CUSTFEATURE=3,1" | MiniPCI-e | | Huawei ME909u-521 | | | v6.11 | | MiniPCI-e | | Huawei MU609 | | | v6.11 | | MiniPCI-e | | Huawei MU709s-2 | | | v6.28 | | MiniPCI-e | | Huawei MS2372h-517 | | | v7.12beta3 | ppp/serial interface | USB | | Jaton MT421e | | | v6.40RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43 | MiniPCI-e | | Netgear Unite Explore 815S | | | v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB | | Novatel USB730L | | | v6.41RC6 | LTE interface | USB | | Olivetti Olicard 500 | | | v6.41RC11 | ppp interface | USB | | Quectel EC20/EC21 | | | v6.xx | ppp interface | MiniPCI-e | | Quectel BG77 | 0x2c7c | 0x0700 | v6.47 | Serial/PPP interface, single AT/modem channel | OEM module | | Quectel BG95-M3 | | | v6.47 | Serial/PPP interface, single AT/modem channel Will not work on wAP R ac boards. | mini-PCIe | | Quectel BG96 | | | v6.45 | Serial/PPP interface, 2x AT/modem channels | mini-PCIe | | Quectel EC25-EU | 0x2c7c | 0x0125 | v6.42 | ppp/LTE interface. RouterOS v6 CDC-ECM mode - LTE interface receive address in modem's internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. | MiniPCI-e | | Quectel EG25-G | 0x2c7c | 0x0125 | 6.48.3 | RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. On some boards it may be required to disable SIM hot plug detection: ```/interface/lte/set [find] modem-init="AT+QSIMDET=0,1"``` | MiniPCI-e | | Quectel EM12-G | 0x2c7c | 0x0512 | v7.1beta5 | MBIM driver | m.2 | | Quectel EP06 | | | v6.42 | ppp/LTE interface | MiniPCI-e | | Quectel RG255C-GL | | | v7.18 | Basic support with at-chat, minimum firmware revision: RG255CGLABR01A04M4G\_A0.004.A0.004 Modem composition: `at+qcfg="usbnet",0` | mini-PCIe | | Quectel RM500Q-GL | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 | | Quectel RM500Q-AE | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 | | Quectel RM502Q-AE | 0x2c7c | 0x0800 | v7.1beta5 | MBIM driver | m.2 | | Quectel RM510Q-GL | 0x2c7c | 0x0800 | 7.9 | MBIM driver | m.2 | | Quectel UC15 | | | v6.xx | Works, ppp interface | MiniPCI-e | | Quectel UC20 | | | v6.xx | Works, ppp interface | MiniPCI-e | | R11e-4G | 0x2cd2 | 0x0003 | v6.42 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e | | R11e-LTE6 | 0x2cd2 | 0x0004 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e | | R11e-LTE | 0x2cd2 | 0x0001 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e | | Sierra Netgear AirCard 320U | | | 6.41 | Customer tested the modem with firmware 03.05.23 | USB | | Sierra wireless MC73xx | | | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface with the modem switched to expose the MBIM interface. MC7304 tested with firmware SWI9X15C\_05.05.67.00 | MiniPCI-e | | Sierra Wireless MC7430 | | | v6.xx and higher | Data channel 2, Info channel 2, Modem init: AT+CGATT=0, Dial-command: AT+CGATT=1;D\*99#, also needs 3.0 pins isolated (PINS:23,25,27,31,33) | MiniPCI-e | | Sierra Wireless MC74xx | | | v7.1 | Basic functionality support for modems with MBIM interface/USB composition | mini-PCIe | | Sierra Wireless MC7455 | | | v7.3beta37 | MBIM mode with extended support for USB compositions: 1009 - diag,modem,mbim100D - diag,nmea,modem,mbim | mini-PCIe | | Sierra Wireless MC7710/MC7700/MC7750 | | | v5.25, v6.0 and 6.40RC43 | If the modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again. | MiniPCI-e | | SIMcom SIM5360 | | | v6.xx | Works! Using PPP interface, vendor-id="0x05c6" device-id="0x9000" | MiniPCI-e / USB w/ converter | | SIMcom SIM7100 | 0x1e0e | 0x9001 | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. | MiniPCI-e / USB w/ converter | | SIMCom SIM8202G-M.2 | | | v7.11 | MBIM driver supported: AT+CUSBCFG=usbid,1e0e,901e | m.2 | | SXT LTE | | | v6 | LTE interface. Old version of SXT LTE | Built-in | | Tele2.ru LTE-D402 | | | v6.47 | Config-less LTE interface | | | Telecom NZ T-Stick ZTE MF-181 | | | v6.0rc13 | Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=\*99#. Tested ok for both data and SMS on CCR1016-12G | USB | | Telit FN980m | | | v7.5 | AT#USBCFG=2 | m.2 | | Telit LE910 | 0x1bc7 | 0x1201 | v6.xx | ppp interface | MiniPCI-e | | Telit LE910C1 | | | v6.46 | Non-configurable from RouterOS | MiniPCI-e | | Telit LM940 | | | v6.44 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | | Telit LM960 | | | v6.46 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | | TPS (Turning Point Solution) GCT450 | | | v6.48 | Config-less LTE interface | MiniPCI-e | | Vodafone (Huawei) K4203 | | | v7.xx | Not supported in ROS v6, but as this modem supports MBIM driver support will be possible in ROS v7. | USB | | Vodafone K4201-Z | | | v6.8 | Some settings are ignored. LTE interface. | USB | | Vodafone K4305 | | | v6.7 | Some settings are ignored. | USB | | Vodafone K5160 | | | v6.37 | Some settings are ignored. | USB | | Yota LU150 | | | v5.22 and v6.4 | Some settings are ignored. | USB | | Yota wifi modem | | | v6.7 | Some settings are ignored. | USB | | Yota WLTUBA-107 | | | v6.0 | Some settings are ignored. | USB | | ZTE 821D | | | v6.x | Set Info channel = 1, Data channel = 3, Dial command=ATDT | USB | | ZTE AC5730 | | | v6.x | | USB | | ZTE ME3630-E | | | v6.40RC26 | ppp and LTE interface | MiniPCI-e | | ZTE MF110 | | | v6.28 and higher | Set info channel = 2, data channel = 2, Dial command=ATM1L3DT | USB | | ZTE MF823 | | | v6.8 | Some settings are ignored. For some devices it's needed to enter FACTORY mode to change operating state. | USB | | ZTE MF825A | | | v6.xx | Some settings are ignored. | USB | | ZTE MF827 | | | v6.8 | Some settings are ignored. | USB | | ZTE MF832S | | | v7.10 | Config-less support, may require to set some settings using at-chat or modem init string | USB | | ZTE MF833U1 | 0x19d2 | 0x1405 | v7.20.6 | Config-less LTE interface | USB | | ZTE MF90 | | | v6.44beta32 and higher | LTE interface | USB | :::warning Not all modems are listed. Localized and locked units may have compatibility issues. ::: For some modems with USB3.0 support in some cases USB3.0 pins need to be isolated to ensure correct initialization: ![](./img/peripherals-01.webp) ## SFP modules | Brand | Model | Rate | Connector/Cable type | Wavelength | Tested with | Works / Doesn't | | :-- | :-- | :-- | :-- | :-- | :-- | :-- | | MikroTik | S-85DLC05D | 1,25G | Dual LC, MM | 850nm | \*Check: [SFP/SFP+ compatibility reference table](../wired-connections/mikrotik-wired-interface-compatibility.mdx) | Natively supported | | MikroTik | S-31DLC20D | 1,25G | Dual LC, SM | 1310nm | \*Check: [SFP/SFP+ compatibility reference table](../wired-connections/mikrotik-wired-interface-compatibility.mdx) | Natively supported | | MikroTik | S-35LC20D | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | \*Check: [SFP/SFP+ compatibility reference table](../wired-connections/mikrotik-wired-interface-compatibility.mdx) | Natively supported | | MikroTik | S-53LC20D | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | \*Check: [SFP/SFP+ compatibility reference table](../wired-connections/mikrotik-wired-interface-compatibility.mdx) | Natively supported | | MikroTik | S-RJ01 | 1000/100/10 | RJ45, Cat5/Cat6 | N/A | \*Check: [SFP/SFP+ compatibility reference table](../wired-connections/mikrotik-wired-interface-compatibility.mdx) | Natively supported | | Axiom | AXG91632 | 1000BASE-LX | Dual LC | 1310nm | CRS125-24G-1S-RM | Works! | | Finisar | FCLF-8521-3 | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | Finisar | FCLF-8521-3-MD | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | Finisar | FTRJ8519P1BNL-B1 | 10/100/1000 1.25 Gb/s 1000Base-SX Ethernet | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | Finisar | FTLF8519P2BNL | 10/100/1000 1.25 Gb/s 1000Base-SX Ethernet | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | Finisar | FTRJ1319P1BTL | 1.25Gb/s 1000Base-LX Ethernet | Dual LC, SM | 1310nm | CCR1009-8G-1S-1S+ and CCR1009-7G-1C-1S+ | Works! | | Unica | SFP-1.25G-T | 1000M | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | Dell | FTLX8571D3BCL | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | Unica | GP-3124-L2CD-C | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! | | Cisco | GLC-T | 1.25G | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | Cisco | GLC-SX-MM | 1000BASE-SX SFP transceiver module for MMF, 1.25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | Cisco | SFP-GE-L | 1000BASE-LX/LH SFP transceiver module for SMF, 1.25G | Dual LC, SM | 1300nm | Various MT hardware | Works! | | 6COM | 6C-SFP-T | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | 6COM | 6C-WDM-0210BSD | 1,25G | BiDi SC, SM | Tx:1550nm/Rx:1310nm | RB2011LS-IN | Works! | | 6COM | 6C-WDM-0210ASD | 1,25G | BiDi SC, SM | Tx:1310nm/Rx:1550nm | RB2011LS-IN | Works! | | 6COM | 6C-SFP-0310D | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! | | 6COM | 6C-SFP-0301D | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | Ingellen | INSP-T(10/100/1000) | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | Ingellen | INSPL-53-BX | 1,25G | BiDi LC, MM | 1550/1310 | RB2011LS-IN | Works! | | Ingellen | INSPL-35-BX | 1,25G | BiDi LC, MM | 1310/1550 | RB2011LS-IN | Works! | | Ingellen | INSP-LX-SM | 1,25G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! | | Ingellen | INSP-SX-MM | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | AXCEN | AXGT-R1T4-05I1 | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! | | AXCEN | AXGD-37А4-0531 | 1,25G | BiDi LC, MM | Tx:1550nm/Rx:1310nm | RB2011LS-IN | Works! | | AXCEN | AXGD-16А4-0531 | 1,25G | BiDi LC, MM | Tx:1310nm/Rx:1550nm | RB2011LS-IN | Works! | | AXCEN | AXGD-1354-0531 | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! | | AXCEN | AXGD-5854-0511 | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! | | TP-Link | TL-SM311LS | 1,25G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! | | TP-Link | TL-SM311LM | 1,25G | Dual LC, MM | 850nm | CCR1036 12G-4S | Works! | | OPTIC | OPTIC-SFP-3524S-02-SC | 1,25G | BiDi SC, SM | Tx:1310nm/Rx:1550nm | RB2011UAS-RM, RB260GS | Works! | | OPTIC | OPTIC-SFP-5324S-02-SC | 1,25G | BiDi SC, SM | Tx:1550nm/Rx:1310nm | RB2011UAS-RM, RB260GS | Works! | | OPTIC | OPTIC-SFP-S1203-L3302-LC | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | RB2011UAS-RM, RB260GS | Works! | | OPTIC | OPTIC-SFP-S1205-L3302-LC | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | RB2011UAS-RM, RB260GS | Works! | | ROBOFiber | SFP-7120-55 | 1,25G | Dual LC, SM | 1550nm | CCR1036-12G-4S, RB2011 | Works! | | ROBOFiber | SFP-7120-WA | 1,25G | BiDi LC, MM | Tx:1490nm/Rx:1550nm | CCR, RB2011 | Works! | | ROBOFiber | SFP-7120-WB | 1,25G | BiDi LC, MM | Tx:1550nm/Rx:1490nm | CCR, RB2011 | Works! | | Enguity | SFP-3647603KM.b1310 XT | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | CCR, RB2011, RB260GS | Works! | | Enguity | SFP-3647603KM.b1550 XT | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! | | Enguity | SFP-3647610KM.b1490 XT | 1,25G | BiDi LC, SM | Tx:1490nm/Rx:1550nm | CCR, RB2011, RB260GS | Works! | | Enguity | SFP-3647610KM.b1550 XT | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1490nm | CCR, RB2011, RB260GS | Works! | | AdvOptics MSA | GLC-SX-MM | 1,25G | BiDi LC, MM | Tx:1310nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! | | AdvOptics MSA | GLC-ZX-SM | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! | | Proline | GLC-BX-D20-PRO | 1,25G | BiDi LC, SM | Tx:1490nm/Rx:1310nm | CRS125 | Works! | | Proline | GLC-BX-D40-PRO | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1490nm | CRS125 | Works! | | Foundry Networks | E1MG-BXU-AC | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1490nm | RB3011UiAS, hAP ac | Works! | | Avago | SFBR-5799APZ | 1,25G | Dual LC, MM | 850nm | CRS326, CRS112 | Works in 1Gbps mode! | | Eltex | NTU-SFP-100 | 1,25G | SC | N/A | RB4011iGS+ | Works! | ## SFP+ modules | Brand | Model | Distance | Rate | Connector/Cable type | Wavelength | Tested with | Works / Doesn't | | :-- | :-- | :-- | :-- | :-- | :-- | :-- | :-- | | MikroTik | S+85DLC03D | 300m | 10G | Dual LC, MM | 850nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+31DLC10D | 10km | 10G | Dual LC, SM | 1310nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+23LC10D | 10km | 10G | BiDi LC, SM | Tx:1270nm/Rx:1330nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+32LC10D | 10km | 10G | BiDi LC, SM | Tx:1330nm/Rx:1270nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+DA0001 | 1m | 10G | Twinax Copper | N/A | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+DA0003 | 3m | 10G | Twinax Copper | N/A | All MikroTik products with SFP/SFP+ interfaces | Natively supported | | MikroTik | S+RJ10 | various, depending on link rate. Check brochure for more details | 10G/5G/2.5G/1G/100M/10M | RJ45 - Cat5E/Cat6/Cat7 | N/A | All MikroTik products with SFP+ interfaces | Natively supported | | Atop | APSP55B30CDL40 | 40km | 10G | Dual LC, SM | 1550nm | CRS series, CCR series devices with SFP+ interfaces | Does NOT work! | | Cisco | SFP-10G-LR | 10km | 10G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! | | Dell (Finisar) | FTLX8571D3BCL | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! | | Juniper (Finisar) | FTLX8571D3BCL-J1 | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! | | Intel (Finisar) | FTLX8571D3BCV-IT | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! | | OEM (Juniper?) | EX-SFP-10GE-SR-OEM | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! | | Fiberstore | SFP-10G31-40 | 40km | 10G | Dual LC, SM | 1310nm | CRS series, CCR series devices with SFP+ interfaces | Works! | | Fiberstore | SFP-10G55-40 | 40km | 10G | Dual LC, SM | 1310nm | CRS series, CCR series devices with SFP+ interfaces | Works! | | Fiberstore | SFP-10G32-40 | 40km | 10G | BiDi LC, SM | Tx:1330nm/Rx:1270nm | CRS series, CCR series devices with SFP+ interfaces | Works! | | Fiberstore | SFP-10G23-40 | 40km | 10G | BiDi LC, SM | Tx:1270nm/Rx:1330nm | CRS series, CCR series devices with SFP+ interfaces | Works! | | Optech | OPAK-TX1-00-C | 30m | 10G | RJ45 - Cat 6a/7 Cable | N/A | CCR, CCR, CSS series devices with SFP+ interfaces | Works, starting with v6.40rc20 RouterOS build. | | ProLabs | SFP-10G-T-C | 30m | 10G | RJ45 - Cat 6a/7 Cable | N/A | CCR, CCR, CSS series devices with SFP+ interfaces | Works, starting with v6.40rc20 RouterOS build. | ## U.2 Disks for RDS The RDS2216-2XG-4S+4XS-2XQ supports U.2 SSD drives of any capacity, with a physical height limitation of 7mm. While any drive meeting this physical requirement should be supported, the following models has been verified: - Samsung PM9A3 - Samsung PM983 - Micron 7300 series - Micron 7400 series - WD DC SN640 - Transcend UTE210T - Innodisk 4TG2-P